- What is the difference between Dana 44 and Dana 60?
- Are Dana 50 and 60 hubs the same?
- What is a live front axle?
- What is a Ford unibody truck?
- Is the Dana 50 a good axle?
- When did Ford stop making the f100?
- Are solid axles better?
- What does the F stand for in Ford F Series?
- What is a Monobeam front axle?
- What is a Twin I Beam suspension?
- What are the differences between the Dana 44 and Dana 50?
- What does XLT mean?
- When did Ford stop using Twin I Beam?
- What year f150 to avoid?
- Do I have a Dana 50 or 60?
- How does Twin Traction Beam work?
What is the difference between Dana 44 and Dana 60?
The Dana 44 axles use u-joints that measure 2.18 inches from snap ring to snap ring.
The Dana 60 axle uses u-joints that measure three inches from snap ring to snap ring.
The Dana 60 has a larger ring gear, larger axle tubes, larger axle shafts, and overall is much stronger..
Are Dana 50 and 60 hubs the same?
Spindle, wheelbearing hubs, and lockouts are the same. Brakes for ’95-97 Dana 60. Balljoints are the same.
What is a live front axle?
A live axle is a type of beam axle in which the shaft (or, commonly, shafts connected to move as a single unit) also transmits power to the wheels; a beam axle that does not also transmit power is sometimes called a dead axle.
What is a Ford unibody truck?
Along with the traditional separate Flareside beds, Ford introduced unibody trucks. These were originally named as the “integrated pickup” and consisted of the cab and the bed into one continuous piece, with no gap between them.
Is the Dana 50 a good axle?
In fact, the Dana 50 and 60 high-pinion Super Duty axles have more in common than you might realize. As you may infer from its name, the Dana 50s overall size and strength rest between that of a Dana 44 and Dana 60. For those looking to run up to a 37-inch tire, the Dana 50 is well-suited.
When did Ford stop making the f100?
1984End of the line Ford stopped making the 4-wheel-drive F100 in 1978 and stopped producing the F100 itself in 1984.
Are solid axles better?
A solid axle setup can improve traction over big bumps and hills as well as gain more torque from the differential as there are fewer parts that power must transfer through. Solid axles are also more durable than most IFS axles and can be easily changed in comparison, making axle repairs on off-road trucks no problem .
What does the F stand for in Ford F Series?
In 1948, Ford debuted the first official F-Series, aka the Ford Bonus-Built line. They ranged from the half-ton F-1, all the way up to the 3-ton F-8. … According to Consumer Guide, because ‘F’ stands for ‘Ford’.
What is a Monobeam front axle?
Monobeam is the solid front axle in the 4X4’s.
What is a Twin I Beam suspension?
In 1965, Ford introduced it’s Twin I-Beam front suspension. … Ford’s revolutionary new Twin-I-Beam suspension gives you two front axles – two rugged I-beam axles to share the abuse of the roughest going! And because of forged steel I-bean construction – just like big-truck axles use – they’ll stand up in severe service!
What are the differences between the Dana 44 and Dana 50?
The Dana 50 has a “50” cast in to the housing and is regarded to have more strength than a Dana 44, but not as much as a Dana 60. It was only produced in a reverse cut gear set aka a high pinion.
What does XLT mean?
It does not mean extra large truck.(XLT) XL is the basic model with the bare bones features. XLT, is the heavy duty model. Heavy duty suspension, electric windows ,etc… Eddie Bauer has heavy duty package as far as the drive train and suspension, and a special trim package, designed by Eddie Bauer and Ford.
When did Ford stop using Twin I Beam?
Twin I-Beams and Twin Traction Beams were utilized on various F-Series trucks until 2002. A Each heavy-duty coil spring can compress and expand on its own, without disturbing the opposite wheel.
What year f150 to avoid?
2004There were a great many wonderful and reliable trucks and engines in this period, but one to avoid is the 2004 F-150, which is known for having one of the worst engines in the history of automobiles.
Do I have a Dana 50 or 60?
The 60 will have the number “248” cast in the web on the center chunk (248mm ring gear). The 50 will have a “229” cast in the web.
How does Twin Traction Beam work?
It uses a universal joint in the center that allows the wheels to move independently of each other. The differential is offset to the driver’s side, and a slip yoke is used on the long axle side to allow the shaft to change length. The TTB axles are variations of the Dana 28, Dana 35, Dana 44, and Dana 50.